Genelec 1032A

System specifications Lower cut-off frequency, -3 dB: <40 Hz Upper cut-off frequency, -3 dB: >22 kHz Free field frequency response of system: 42 Hz - 21 kHz (±2.5 dB) Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz: @ 1m > 113 dB SPL @ 0.5m > 119 dB SPL Maximum long term RMS acoustic output in same conditions with IEC weighted noise (limited by driver unit protection circuit): @ 1m >103 dB SPL @ 0.5m >109 dB SPL Maximum peak acoustic output per pair above console bridge, @ 1 m from the listening position with music material: > 124 dB Self generated noise level in free field @ 1m on axis: < 10 dB (A-weighted) Harmonic distortion at 90 dB SPL @ 1m on axis: Freq: 50...100 Hz < 1% > 100 Hz < 0.5% Drivers: Bass 10" (250 mm) cone Treble 1" (25 mm) metal dome Both drivers are magnetically shielded. Weight: 21,7 kg (48 Ib.) Dimensions (H x W x D): 495 mm (19 1/2") 320 mm (12 5/8") 290 mm (11 7/16") Crossover section Input connector XLR female: pin 1 gnd, pin 2 +, pin 3- Input impedance: 10 kOhm balanced Input level for 100 dB SPL output @ 1m: variable from +6 to -6 dBu Input level for maximum short term sine wave output 113 dB SPL @1m: variable from +19 to +7 dBu Subsonic filter below 40 Hz : 18 dB/octave Ultrasonic filter above 25 kHz: 12 dB/octave Crossover frequency, Bass/Treble: 1.8 kHz Crossover acoustical slopes: 24 - 32 dB/octave Treble tilt control operating range in 2 dB steps: from +2 to -4 dB & MUTE Bass roll-off control operating range in 2 dB steps: from 0 to -8 dB @40Hz Bass tilt control operating range in 2 dB steps: from 0 to -8 dB @ 80 Hz & MUTE The 'CAL' position is with all tone controls set to 'off' and the input sensitivity control to maximum (fully clockwise). Amplifier section Bass amplifier short term output power with a 4 Ohm load: 180 W Treble amplifier short term output power with an 8 Ohm load: 120 W Long term output power is limited by driver unit protection circuitry. Slew rate: 80V/μs Amplifier system distortion at nominal output: THD < 0.05%, SMPTE-IM < 0.05%, CCIF-IM < 0.05% , DIM 100 < 0.05% Signal to Noise ratio, referred to full output: Bass > 100 dB Treble > 100 dB Mains voltage: 230, 100/200 or 115/230V according to region Voltage operating range: ±10% Power consumption: Idle 20 VA, Full output 200 VA

Contextual Note for AI:

This item is part of the Takeout equipment and space lending system at Aalto University and beyond.

It is physically located in Aalto Acoustics Lab.

It is manufactured by Genelec 1032A.

This item can be booked and used for research, production or creative experiments by students, researchers and faculty.

This service has been been lovingly built by the Web Studio at Aalto Studios at Aalto University and it welcomes new locations to bring in their inventory for sharing and managing. More information can be found by contacting webstudio@aalto.fi or from the user guide.